A word of warning here – this kit is not something you would use for a quick build. I found that the hard way as you would find out below.
Due to the zimmerit being molded in the kit parts the hull is comprised of new parts. Whether the “smooth” Panthers fit OK I am unaware as of now, but this one certainly had issues with a bunch of shims required all around the front and back to make gaps go away. You can also see the large gap around the ball MG mount – still not filled here…
I got the kit in 2010 as a replacement for a lost package – I had won an “Achtung, Jabo!” pack with 4 figures, which never arrived for whatever reason.
Actually this was my first Dragon tank and I was eager to open the box and see what’s in. DML didn’t fail to impress. The number of parts is rather large due to sprue sharing with other Ausführungs and even with the Jagdpanther.
Onto the images (click to see larger images). You get sprue A, which is wheels and side armor screens.
Time to show the finished product.
Decals as per DML’s instructions. I used the 4 in the red circle and it’s a good think the Dragon boys and gals had included a spare. Decals were tamed using my favorite Mr. Mark Softer from Gunze, then covered with Vallejo matt varnish.
Since the tank has been painted with about 7 variations of green I used a bit less pigment powders (Agama Sand, Dust and a bit of white) than usual to weather it. A bit of black behind the exhausts, around machine guns and gun muzzle and again a coat of Vallejo flat.
Another Armorama review build. This was one of those rare occasions when I decided to strictly follow the instructions.
I started by test-fitting the turret top and bottom. The locating pins in the turret base detail are too thick, so a step step was formed – they were quickly removed.
Since two options were presented for the main turret armament (parts C3 and B7) I went with the longer one 🙂 The aft end of the detail required some sanding to fit in the turret mask. Next, the Besa machine gun was glued in the mask. After the assembly was glued to the turret base (C5), I added the top detail (C9) to close the turret.
Well,considering the aging releases by ESCI, Airfix and Hasegawa the Braille scale world has been aching for a modern kit of this important machine for quite some time. Well – here’s DML’s attempt.
The kit contains 70 parts:
Oh I hear your cries about NO PE parts, but rest assured – this is a non-issue with the kit.
There are two main hull components, cast as separate parts – the upper one represents the top deck and the fenders, and lower part is the slide-molded hull tub.
It is interesting to note that there are fuel can racks at the aft end of the fenders, and Dragon has included two pairs of British-style 2 gallon cans to be posed there should the modeler so desire.
I painted the entire composition with Revell enamels – 79 being the main color and 57 as well as mixes of the two used to vary the shades in different places. I also added the white rectangles on both the Horch and trailer fenders, but these almost disappeared under the dust I applied later.
Seats were brushed with Revell 381 and given a thin acrylic wash to accentuate the molded-on uneven surface (again a nice touch by Dragon). Tires were sprayed Revell 78 to simulate a bleached/dusty effect, and then added to the vehicle body and the trailer. The exhaust pipes and muffler were basecoated with Revell 37 to simulate rust and glued on the vehicle. I then proceeded to add some metal chips by drybrushing Tamiya’s X11.
Since I got the kit to build as a reviewer for Armorama I started almost immediately after taking the pics. Here’s how the build went through.
I started by adding the lower engine compartment/radiator face and the firewall to the vehicle body.
Other than filling the seam line in the front wheel arches these fit fine.
Next step was the suspension. After carefully studying reference images I glued parts B9 and B10 first, and then proceeded to add the suspension arms.
Please note that all 4 parts are labeled B7, but the parts intended for the rear axle have an extra pair of locating pins. With these fixed I glued the 8 springs (parts B8) to parts B10 and B11. So far fit has been very good. I cut off the representation of the rubber mudguards and replaced them with thick aluminum foil.
Well the DML people kinda got it wrong, because the box top says “Typ 40”, where the boxart and the parts depict the earlier version (Typ 1a). It has the spare wheels exposed on the vehicle body sides, while the Typ 40 has flat side walls, as the spare wheels are located inside the vehicle body.
The kit contains 91 parts, including
The Dragon team has simply included one of the vehicles found in the Horch 1+1 combo (kit 7378) and added a towed 20mm AA gun.
There are 54 parts used for the Horch “jeep”. 50 of those are located on sprue B.
It’s finally done. After the splattering nozzle my masterful hobby-time organizational skills delayed this pic set.
Tracks: as most of them is rubber – Revell 78 was used to mimicking the areas. Glued over the wheels (sand center + 78 again for the rubber bandages) with Loctite gel. Inserted Q-tips to provide the sag – worked like a charm!
Cupola vision blocks were done the following way:
– the recesses were brushpainted Tamiya XF-11;
– Revell enamel transparent blue was mixed with their own gloss cote and painted over the XF-11;
Alright, it’s been a while since I started this kit, and the source of the delay has been the overspray due to cracked airbrush nozzle. While waiting for a replacement I replaced most of the detail on the top.
I removed the antiskid plates (don’t ask – don’t tell) and re-did the antislip coating only. Few of the original plastic handholds are still in use, most were replaced with wire – as were the DML PE parts, since most were too flimsy and two-dimensional. I also added the rope tie-downs at the 4 corners.